Stainless steel throughout with satin finish on all exposed surfaces; welded construction.
Mounts through partitions 1/2" to 2" (13-51mm) thick, serving two compartments, used from both sides, serviced from one side.
Flanges are one-piece seamless, door secured with full-length stainless steel hinges, and tumbler lock.
Dispenses 1000 toilet seat covers and four rolls of tissue, accommodates 5-1/4" (135mm) dia. 1800-sheet rolls, two each for each compartment.
Toilet tissue on right when facing unit.
Cabinet — 18-8 S, type-304, heavy-gauge stainless steel. All-welded construction. Exposed surfaces have satin finish. Equipped
with a plastic sight-barrier panel for toilet-seat-cover dispenser.
Flanges (2) — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn and beveled, one-piece, seamless
Door & Permanent Panel — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. One?piece, seamless
construction. Door is secured to cabinet with a full-length stainless steel piano-hinge and equipped with two tumbler locks
keyed like other Bobrick washroom accessories.
Toilet Tissue Dispensers (4) — .100" (2.5mm) thick ABS. Equipped with four theft-resistant, heavy-duty, one-piece, molded
Toilet-seat-cover dispenser is serviced from one side and holds 1000 single- or half-fold paper covers. Door unlocks with key
provided and swings open for filling. Spindles may be removed from cabinet only when door is open. Unit holds four standardcore
toilet tissue rolls up to 5-1/4'' (135mm) diameter (1800 sheets), two for each compartment.
Designer's Note: It is recommended that one full toilet tissue roll remain wrapped until the other roll has been depleted to avoid
wasting ends of both rolls.
Mount unit in toilet partition 1/2'' to 2'' (13 x 51mm) thick, centered through a cutout specially ordered from partition
manufacturer or field cut. Dimensions of cutout are to be 15-1/2" wide x 28-7/8" high (395 x 735mm). For factory-made cutouts,
location and size details must be furnished to partition manufacturer. For hollow-core metal partitions, provide solid framing
into which sheet-metal mounting screws can be secured.
For installation with sheet-metal screws furnished, place unit firmly in partition cutout, making certain entire perimeter of fixed
flange is flush with and tight against partition surface. Secure to partition with sheet-metal screws through four mounting holes
at points indicated by an S. On other side of partition, position adjustable flange (which serves as an escutcheon) so mounting
holes are not inline with mounting holes in fixed flange. Make certain entire perimeter of adjustable flange is flush with and
tight against partition surface before securing with sheet-metal screws furnished.
For through-bolting method of installation, make sure mounting holes in adjustable flange are inline with holes in fixed flange.
Using adjustable flange as template to mark locations, drill 7/32" or 1/4" (5.5 or 6.4mm) holes through partition. Provide
four binder posts and #6 (3.5mm) flat-head screws to secure unit and its adjustable flange. Obtain binder posts and screws by
ordering Bobrick Binder Post Kit No. 354-119 for partitions 1/2" (13mm) thick only or Kit No. 354-124 for partitions 3/4" to
1-1/4" (19 to 32mm) thick.
Note: Cutouts in Bobrick toilet partitions can be pre-cut for Bobrick partition-mounted accessories at factory if location and size
of cutouts are specified and order for both partitions and accessories are received together.
Partition-mounted toilet-seat-cover and toilet tissue dispenser shall be type-304 stainless steel with all-welded construction; exposed
surfaces shall have satin finish. Toilet tissue dispenser shall be ABS plastic. Flanges shall be drawn and beveled, one-piece,
seamless construction. Unit shall mount in partition and serve two toilet compartments. Door shall be one-piece, seamless
construction; secured to cabinet with a full-length stainless steel piano-hinge; and equipped with two tumbler locks keyed like
other Bobrick washroom accessories. Toilet-seat-cover dispenser shall be serviced from one side only, equipped with a plastic
sight-barrier panel, and hold 1000 paper covers. Unit shall be equipped with four theft-resistant, heavy-duty ABS toilet tissue
spindles that hold standard-core rolls up to 5-1/4'' (135mm) diameter (1800 sheets). Spindles shall be removable from cabinet
only when door is open. Manufacturer’s service and parts manual shall be provided to the building owner/manager upon
Partition-Mounted Seat-Cover And Toilet Tissue Dispenser shall be Model B-347 of Bobrick Washroom
Equipment, Inc., Clifton Park, New York; Jackson,
Tennessee; Los Angeles, California; Bobrick Washroom
Equipment Company, Scarborough, Ontario; Bobrick Washroom Equipment Pty. Ltd., Australia; and Bobrick
Washroom Equipment Limited, United Kingdom.