Bobrick B-3474 Classic Series Recessed Seat-Cover and Toilet Tissue Dispenser
Stainless steel throughout with satin finish on all exposed surfaces; welded construction.
For recessed installation in side wall of single compartment.
Flange is one-piece seamless, door secured with full-length stainless steel hinges, and tumbler lock.
Dispenses 500 toilet seat covers and two rolls of tissue, accommodates 5-1/4" (135mm) dia. 1800-sheet rolls.
Toilet tissue is on the right when facing unit.
Cabinet — 18-8 S, type-304, heavy-gauge stainless steel. All-welded construction. Exposed surfaces have satin finish.
Flange — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish. Drawn and beveled, one-piece, seamless construction.
Door — 18-8 S, type-304, 18-gauge (1.2mm) stainless steel with satin finish. One-piece, seamless construction. Secured to cabinet with a full-length stainless steel piano-hinge. Equipped with a tumbler lock keyed like other Bobrick washroom accessories.
Permanent Panel — 18-8 S, type-304, 22-gauge (0.8mm) stainless steel with satin finish.
Toilet Tissue Dispensers (2) — .100" (2.5mm) thick ABS. Equipped with two theft-resistant, heavy-duty, one-piece, molded ABS spindles.
Door unlocks with key provided and swings open for filling. Toilet-seat-cover dispenser fills from below the internal shelf and holds 500 single- or half-fold paper covers. To remove spindle, remove core of toilet tissue first. Then, insert end of special key furnished by Bobrick into slot in face of spindle and slide retractable plunger back, releasing spindle. Unit holds two standard-core toilet tissue rolls up to 5-1/4" (135mm) diameter (1800 sheets).
Designer's Note: It is recommended that one full toilet tissue roll remain wrapped until the other roll has been depleted to avoid wasting ends of both rolls.
Provide framed rough wall opening 16" wide x 29-1/4" high (405 x 745mm). Minimum recessed depth required from finish face of wall is 4" (102mm). Top of wall opening should be 42-1/4" (1075mm) from finish face of floor with rear edge of opening 20'' (510mm) from back wall of compartment to allow placement of horizontal grab bar at 33" (840mm) height across front of unit. Allow clearance for construction features that may protrude into rough wall opening from opposite wall. Coordinate with mechanical engineer to avoid pipes, vents, and conduits in wall. If unit projects above top of wainscot, provide aluminum channel or other filler to eliminate gap between flange and finish face of wall. Mount unit in wall opening
with shims between framing and cabinet at all points indicated by an S, then secure unit with #8 x 1-1/4" (4.2 x 32mm) sheet-metal screws (not furnished).
Bobrick B-3474 Spec Sheet
Recessed toilet-seat-cover and toilet tissue dispenser shall be type-304 stainless steel with all-welded construction; exposed surfaces shall have satin finish. Toilet tissue dispenser shall be ABS plastic. Flange shall be drawn and beveled, one-piece, seamless construction. Unit shall mount flush against side wall of barrier-free toilet compartment to allow clearance for grab bar across front of unit. Door shall be one-piece, seamless construction; secured to cabinet with a full-length stainless steel piano-hinge; and equipped with a tumbler lock keyed like other Bobrick washroom accessories. Toilet-seat-cover dispenser shall fill from below the internal shelf and hold 500 paper covers. Unit shall be equipped with two theft-resistant, heavy-duty ABS toilet tissue spindles that hold standard-core rolls up to 5-1/4" (135mm) diameter (1800 sheets). Spindle shall have a
concealed locking mechanism opened with special key furnished.